Msi MS-96C8 Series Instrukcja Użytkownika Strona 109
- Strona / 113
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
B-19
LSI SAS RAID
5. Creating Integrated Striping Volumes
This section describes how to create Integrated Striping (IS) volumes using the LSI
Logic SAS BIOS Configuration Utility (SAS BIOS CU).
5.1 IS Configuration Overview
You can use the SAS BIOS CU to create multiple IS volumes, with up to 10 drives total
on an LSI Logic SAS controller. Each volume can have from 2 to 8 drives. Disks in an
IS volume must be connected to the same LSI Logic SAS controller, and the controller
must be in the BIOS boot order.
Although you can use disks of different size in IS volumes, the smallest disk deter-
mines the “logical” size of each disk in the volume. In other words, the excess space
of the larger member disk is not used. Usable disk space for each disk in an IS volume
is adjusted down to leave room for metadata. Usable disk space may be further
reduced to maximize the ability to interchange disks in the same size classification.
The supported stripe size is 64 Kbytes.
Refer to Section 4.2, “IS Features,” for more information about Integrated Striping
volumes.
5.2 Creating IS Volumes
The SAS BIOS CU is part of the Fusion-MPT BIOS. When the BIOS loads during boot
and you see the message about the Setup Utility, press Ctrl-C to start it. After you do
this, the message changes to:
Please wait, invoking SAS Configuration Utility...
After a brief pause, the main menu of the SAS BIOS CU appears. On some systems,
however, the following message appears next:
LSI Logic Configuration Utility will load following initialization!
In this case, the SAS BIOS CU will load after the system has completed its power-on
self test.
Follow the steps below to configure an Integrated Striping (IS) volume with the SAS
BIOS CU. The procedure assumes that the required controller(s) and disks are al-
ready installed in the computer system. You can configure both IM and IS volumes on
the same SAS controller.
1. On the Adapter List screen of the SAS BIOS CU, use the arrow keys to select
a SAS adapter.
PDF created with pdfFactory Pro trial version www.pdffactory.com
- 5500 Master Series 1
- Copyright Notice 2
- Trademarks 2
- Revision History 2
- Technical Support 2
- Safety Instructions 3
- Micro-Star International 4
- CONTENTS 8
- Getting Started 11
- Mainboard Specifications 12
- Back Panel 13
- Onboard Connectors 13
- SYS_FAN3 14
- RECOVERY 14
- JBIOS_WP 14
- Hardware Setup 15
- Quick Components Guide 16
- Alignment Key 17
- CPU & Cooler Installation 18
- Important 19
- Mainboard 20
- 72x2=144 pin 21
- 240-pin, 1.5V 21
- 48x2=96 pin 21
- Power Supply 22
- Back Panel I/O 23
- Connect to JCD1 24
- Connect to 40-pin 24
- IDE device 24
- Connect to 44-pin 24
- Serial Port Connector: COM2 26
- SPI Flash ROM Connector: J2 28
- I2C Bus Connector: JSMBUS1 28
- Front Panel Connector: JSSI1 30
- Clear CMOS Jumper: CLR_CMOS 31
- PCI Express x16 Slot 32
- 32-bit PCI Slot 32
- PCI Express x8 Slot 32
- PCI Express x4 Slot 32
- BIOS Setup 33
- Entering Setup 34
- Getting Help 35
- General Help <F1> 35
- Control Keys 35
- The Menu Bar 36
- Advanced 38
- MS-96C8 Server Board 48
- Temperature Information 48
- Fan Speed Information 48
- Notify BMC FAN Type 48
- Boot Settings Configuration 52
- Security 56
- CPU Bridge Configuration 57
- Intel ICH10R SATA RAID 63
- Appendix A 63
- Introduction 64
- BIOS Configuration 65
- (1) Create RAID Volume 66
- (4) Recovery Volume Options 71
- Installing Driver 72
- Installing Software 74
- RAID Migration Instructions 78
- Recovery Volume Creation 85
- (8) Select an update policy 88
- Degraded RAID Array 89
- LSI SAS RAID 91
- Appendix B 91
- 2.1 Introduction 93
- 2.2 IM Features 94
- 2.3 IM/IME Description 95
- 2.5 Fusion-MPT Support 98
- 3.4 Managing Hot Spares 103
- 3.5 Other Configuration Tasks 104
- 4.1 Introduction 106
- 4.2 IS Features 106
- 4.3 IS Description 107
- 4.5 Fusion-MPT Support 108
- 5.1 IS Configuration Overview 109
- 5.2 Creating IS Volumes 109
- 5.4 Other Configuration Tasks 112
Powiązane produkty i podręczniki dla Sprzęt komputerowy Msi MS-96C8 Series
(81 strony)Hilti PML 42 manuali
Manuali dei proprietari e guide per l'utente per Lavorazione del legno Hilti PML 42.
We fornisce 1 manuali pdf Hilti PML 42 per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Komentarze do niniejszej Instrukcji